This chapter describes LAN Switch Integration (LSI) messages. For information on message content and how to use the message, refer to the Introduction.
| LSI.001 |
Level: U-INFO
Short Syntax: LSI.001 Rcv packet_type len length dom domain from from_hw_add to to_hw_add net network ID
Long Syntax: LSI.001 Received a packet type: packet_type length length on logical port domain from from_hw_add to to_hw_add to net network ID
Description: A frame is received from the lan switch.
Cause: A frame is received from the lan switch.
| LSI.002 |
Level: U-INFO
Short Syntax: LSI.002 Snd type len length dom domain from from_hw_add to to_hw_add net network ID
Long Syntax: LSI.002 Sending a packet type type of length length on domain domain from from_hw_add to to_hw_add from net network ID
Description: A frame is being sent to the lan switch.
Cause: A frame is being sent to the lan switch.
| LSI.003 |
Level: U-INFO
Short Syntax: LSI.003 Frame rcv too big for net Max: max Len: length Elp: elp from from_hw_add to to_hw_add net network ID
Long Syntax: LSI.003 Frame received too large for net Max: max Len: length Elp: elp from from_hw_add to to_hw_add net network ID
Description: A packet is received that is too large to be processed by the net interface.
Cause: A packet is received that is too large to be processed by the net interface.
| LSI.004 |
Level: U-INFO
Short Syntax: LSI.004 Disc frame type len length from dom: domain from from_hw_add to to_hw_add type: elptype
Long Syntax: LSI.004 Discard frame type length length from domain domain from from_hw_add to to_hw_add type: elptype
Description: A packet is received that does not match the addressing of the associated net.
Cause: Packet received that is not needed by the associated nets for this domain, and their configured protocols.
| LSI.005 |
Level: U-INFO
Short Syntax: LSI.005 Rif Walk post bdg Dom: domain DestSeg: sseg SrcSeg pseg ret:
Long Syntax: LSI.005 Rif Walk post bdg Domain: domain DestSeg: sseg SrcSeg pseg ret:
Description: A packet was received from the bridge function that needed to be rerouted to its correct source segment. source bridge segment.
Cause: Packet received post bridge.
| LSI.006 |
Level: P-TRACE
Short Syntax: LSI.006 Trace LSI packet
Long Syntax: LSI.006 Trace LSI packet
Description: Trace an input or output packet.
| LSI.007 |
Level: U-INFO
Short Syntax: LSI.007 VCC Handle: txId added for lcd: vcc domain: domain
Long Syntax: LSI.007 VCC Handle: txId added for lcd: vcc domain: domain
Description: A VCC Handle has been added to this LCD for hardware path.
| LSI.008 |
Level: U-INFO
Short Syntax: LSI.008 TxID: txId added for VCC Handle: vcc domain: domain
Long Syntax: LSI.008 TxID: txId added for VCC Handle: vcc domain: domain
Description: A lan switch transmit channel has been created.
| LSI.009 |
Level: U-INFO
Short Syntax: LSI.009 mac addr mac assigned TxID: txId domain: domain
Long Syntax: LSI.009 mac addr mac assigned TxID: txId domain: domain
Description: A mac address will be associated with a txid, so that packets destined to that address will be switched via hardware from the lan switch to the atm network.
| LSI.010 |
Level: U-INFO
Short Syntax: LSI.010 Route Desc rd assigned TxID: txId domain: domain
Long Syntax: LSI.010 Route Desc rd assigned TxID: txId domain: domain
Description: A route descriptor will be associated with a txid, so that packets destined to that route descriptor will be switched via hardware from the lan switch to the atm network.
| LSI.011 |
Level: U-INFO
Short Syntax: LSI.011 HwPath VCC deleted vcc_id: vcc lcd_p: lcd_p
Long Syntax: LSI.011 HwPath VCC deleted vcc_id: vcc lcd_p: lcd_p
Description: A vcc has been deleted from the bridged hardware path.
| LSI.012 |
Level: U-INFO
Short Syntax: LSI.012 TxId deleted id: txid
Long Syntax: LSI.012 TxId deleted id: txid
Description: A txid has been deleted from the bridged hardware path when the associated VCC has also been deleted.
| LSI.014 |
Level: U-INFO
Short Syntax: LSI.014 mac addr mac reassigned txId: txId domain: domain sw pth
Long Syntax: LSI.014 mac addr mac reassigned txId: txId domain: domain sw pth
Description: A mac address associated with a txid is being reassigned, so that packets destined to that address will be processed by the software to the atm network.
| LSI.015 |
Level: U-INFO
Short Syntax: LSI.015 Route Desc rd reassigned txId: txId domain: domain sw pth
Long Syntax: LSI.015 Route Desc rd reassigned txId: txId domain: domain sw pth
Description: A Route Descriptor associated with a txid is being reassigned, so that packets destined to that route will be processed by the software to the atm network.
| LSI.016 |
Level: U-INFO
Short Syntax: LSI.016 Packet Disc bad Rif len: len domain: domain Intf: intf
Long Syntax: LSI.016 Packet Disc bad Rif len: len domain: domain Intf: intf
Description: A packet was discard that was sent from the software bridge into the lan switch because of a bad rif field in the packet.
Cause: Internal software error.
| LSI.017 |
Level: U-INFO
Short Syntax: LSI.017 Packet Disc bad txid: txid len: len
Long Syntax: LSI.017 Packet Disc bad txid: txid len: len
Description: A packet was discard that was received from the lan switch because of an invalid txchannel.
Cause: Internal software error.
| LSI.018 |
Level: U-INFO
Short Syntax: LSI.018 Snd Pkt Disc no mimic buffer dom: dom, len: len
Long Syntax: LSI.018 Send Packet Disc no mimic buffers dom: dom, len: len
Description: A packet was discarded because there were no mimic buffers available to copy the packet into for transmission into the lan switch.
Cause: Internal software error.
| LSI.019 |
Level: U-INFO
Short Syntax: LSI.019 Get Domain Members Request issued for domain: domain
Long Syntax: LSI.019 Get Domain Members Request issued for domain: domain
Description: The Get Domain Members Request has been issued to the lan switch.
| LSI.020 |
Level: U-INFO
Short Syntax: LSI.020 Get Domain Members Response received for domain: domain
Long Syntax: LSI.020 Get Domain Members Response received for domain: domain
Description: The Get Domain Members Response has been received from the lan switch.
| LSI.021 |
Level: U-INFO
Short Syntax: LSI.021 function:feCrfMembersResponse, LEC Net pointer for domain: domain is 0
Long Syntax: LSI.021 Net pointer for domain: domain is 0
Description: The net pointer associated with the Proxy LEC is invalid.
| LSI.022 |
Level: UE-ERROR
Short Syntax: LSI.022 VCC Handle not available for lcd: vcc domain: domain
Long Syntax: LSI.022 VCC Handle not available for lcd: vcc domain: domain
Description: No more VCC Handles are available for hardware path.
| LSI.023 |
Level: UE-ERROR
Short Syntax: LSI.023 TxID not available for VCC Handle: vcc domain: domain
Long Syntax: LSI.023 TxID not available for VCC Handle: vcc domain: domain
Description: No more Transmit Channel IDs are available for hardware path.
| LSI.024 |
Level: U-INFO
Short Syntax: LSI.024 MPOA mac addr mac was NOT assigned to TxID: txId domain: domain
Long Syntax: LSI.024 MPOA mac addr mac was NOT assigned to TxID: txId domain: domain
Description: The MAC address is an MPOA address and will NOT be associated with a TxID.
| LSI.025 |
Level: UE-ERROR
Short Syntax: LSI.025 net bdg and net rtr are both SRB bridged on domain dom, net network ID disabled
Long Syntax: LSI.025 net bdg and net rtr are both SRB bridged on domain dom, net network ID disabled
Description: Two SRB interfaces, with TWO bridge segements have been assigned to the same domain. This is an invalid configuration, which has resulted in the second of these two interfaces being forced into a disabled state.
| LSI.026 |
Level: U-INFO
Short Syntax: LSI.026 A packet was discarded because the destined net was down
Long Syntax: LSI.026 A packet was discarded because the destined net was down
Description: A packet was discarded beecause its detined net was disabled, or down.
| LSI.027 |
Level: UE-ERROR
Short Syntax: LSI.027 The hw path received a null pointer on rx
Long Syntax: LSI.027 The hw path received a null pointer on rx
Description: An event was received by the hardware bridge from the network interface, that had a null packet pointer.
| LSI.028 |
Level: UE-ERROR
Short Syntax: LSI.028 The hw path detected a PCI error
Long Syntax: LSI.028 The hw path detected a PCI error
Description: The hardware path detected a PCI error. Additional messages may follow that give additional details.
| LSI.029 |
Level: UE-ERROR
Short Syntax: LSI.029 The hw path detected a PCI DMA error
Long Syntax: LSI.029 The hw path detected a PCI DMA error
Description: The hardware path detected a PCI DMA error. Additional messages may follow that give additional details.
| LSI.030 |
Level: UE-ERROR
Short Syntax: LSI.030 The hw path detected a PCI DMA error on the transmit path
Long Syntax: LSI.030 The hw path detected a PCI DMA error on the transmit path
Description: The hardware path detected a PCI DMA error. Additional messages may follow that give additional details.
| LSI.031 |
Level: UE-ERROR
Short Syntax: LSI.031 The hw path detected a PCI DMA error on the receive path
Long Syntax: LSI.031 The hw path detected a PCI DMA error on the receive path
Description: The hardware path detected a PCI DMA error. Additional messages may follow that give additional details.
| LSI.032 |
Level: UE-ERROR
Short Syntax: LSI.032 The hw path detected an error in a packet that was received from the lan switch
Long Syntax: LSI.032 The hw path detected an error in a packet that was received from the lan switch
Description: The hardware path detected an error in the control block header on packet received from the lan switch destined out the network interface.
| LSI.033 |
Level: UE-ERROR
Short Syntax: LSI.033 The hw path detected target abort signal on the PCI bus.
Long Syntax: LSI.033 The hw path detected target abort signal on the PCI bus.
Description: The hardware path detected an error when trying to transfer a packet from, or to the network interface.
| LSI.034 |
Level: UE-ERROR
Short Syntax: LSI.034 The hw path detected master abort signal on the PCI bus.
Long Syntax: LSI.034 The hw path detected master abort signal on the PCI bus.
Description: The hardware path detected an error when trying to transfer a packet from, or to the network interface.
| LSI.035 |
Level: UE-ERROR
Short Syntax: LSI.035 The hw path received a parity error signal from a target.
Long Syntax: LSI.035 The hw path received a parity error signal from a target.
Description: The hardware path detected an error when trying to transfer a packet to the network interface. This was detected on the network side as the packetwas being DMAed into its memory space.
| LSI.036 |
Level: UE-ERROR
Short Syntax: LSI.036 The hw path received a detected a parity on the pci bus.
Long Syntax: LSI.036 The hw path received a detected a parity on the pci bus.
Description: The hardware path detected an error when trying to transfer a packet from the network interface. This was detected on the hardware path side as the packet was being DMAed into its memory space.
| LSI.037 |
Level: UE-ERROR
Short Syntax: LSI.037 The hw path dma was unexpectedly halted.
Long Syntax: LSI.037 The hw path dma was unexpectedly halted.
Description: The hardware path DMA entity was unexpectdly halted. A restart will be attempted, but the hardware path may not be able to recover.
| LSI.038 |
Level: UE-ERROR
Short Syntax: LSI.038 An inv int was reg net network ID/ dom on dom:
Long Syntax: LSI.038 An inv int was reg net network ID/ dom on dom:
Description: A invalid network was registered to the LSI client. This was probably caused by an invalid cofiguration, or a corrupted config.
| LSI.039 |
Level: UE-ERROR
Short Syntax: LSI.039 A hw path reset timed out.
Long Syntax: LSI.039 A hw path reset timed out.
Description: A reset was issued to the hw path, and it timed out before the proper state was attained. This could be the result of a PCI error, or other problems. The system may still be operational.
| LSI.040 |
Level: UE-ERROR
Short Syntax: LSI.040 A hw path looped packet failed.
Long Syntax: LSI.040 A hw path looped packet failed.
Description: A looped packet to the switch was not successfully received. This may result in the a severe error on the system that may require a reset. The system may still be operational.
| LSI.041 |
Level: UI-ERROR
Short Syntax: LSI.041 nt network error_lvl log_point
Long Syntax: LSI.041 network network: lsi error log: error_lvl log_point
Description: lsi generic error
| LSI.042 |
Level: UI-ERROR
Short Syntax: LSI.042 inproper looped frame type len length from dom: domain from from_hw_add to to_hw_add type: elptype
Long Syntax: LSI.042 inproper looped frame type len length from dom: domain from from_hw_add to to_hw_add type: elptype
Description: A frame was received that was inappropiately looped back from the MSS UFC card, back to the MSS card. This may be the result of a back level version of switch micro code.
| LSI.043 |
Level: U-INFO
Short Syntax: LSI.043 loop Snd type len length dom domain from from_hw_add to to_hw_add net network ID
Long Syntax: LSI.043 looping a packet type type of length length on domain domain from from_hw_add to to_hw_add from net network ID
Description: A frame is being sent to the lan switch with the purpose of having the frame looped back into the MSS Card.
| LSI.044 |
Level: U-INFO
Short Syntax: LSI.044 Disc frm out inl: t type dom length len domain from_hw_add -> to_hw_add n network ID
Long Syntax: LSI.044 Disc frame out when in_low set:type type dom length length domain from from_hw_add to to_hw_add net network ID
Description: A frame that was to be sent to the lan switch was discarded because the source interface was in a buffer depleted state.
| LSI.045 |
Level: U-INFO
Short Syntax: LSI.045 Buff not avail for cpy pckt: type: type length length dom domain from from_hw_add to to_hw_add net network ID
Long Syntax: LSI.045 Buff not avail for cpy pckt: type: type length length dom domain from from_hw_add to to_hw_add net network ID
Description: A frame that was to be sent from the LAN Switch to the MSS Card was to be copied to a second net that is configured on this domain. Since the LAN Switch Interface was low on buffers, a copy of the buffer could not be sent to the second interface. If this event happens frequently, it is recomended that the second interface be moved to its own domain if possible, or if the interface is being used for Box Management only, IPHOST be used instead.
| LSI.046 |
Level: U-INFO
Short Syntax: LSI.046 LAN Switch Out queue over flow
Long Syntax: LSI.046 LAN Switch Out queue over flow
Description: The LAN Switch is sending the MSS UFC more taffic than the MSS UFC is capable of receiving at this time. An uspecified number of packets may have been discarded. Although this event should not be considered an error, it may be an indication of network over utilization if this event is received at high rates. Network reconfiguration, or filtering of iproper traffic may lesson this error.